Our new website is available at new.dizzy.co.za :-).

X
+27 (0)11 022 5323 +27 (0)64 681 8495
Basket/Checkout
R
- -
MagnifierSearch:
RS232 SPI click (Go to Parent Category)

RS232 SPI click

RS232 SPI click is based around the MAX3100, a universal universal asynchronous receiver transmitter (UART) - the first UART specifically optimized for small microcontroller-based systems, from Maxim Integrated. Because of the features contained in its modules, the RS232 SPI click can be used for handheld instruments, small networks in HVAC or Building control, UART in SPI systems, battery-powered systems, PDAs, notebooks and many more.

RS232 SPI Click board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

R605  Qty:
Price ex. VAT. Weight: 29g. Stock: Lead-time applicable [i]. mikroE Icon

How does it work?

RS232 SPI click two ICs - MAX3100 and MAX3232. MAX3100 serves as UART interface to the SPI/MICROWIRE compatible interface converter. In the same time, MAX3232 device enables RS232 SPI click to meet the requirements of TIA/EIA-232-F and also provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply.

RS232 SPI click Uses an SPI™/MICROWIRE™ interface for communication with the host microcontroller (µC). Then, the MAX3100 is responsible for conversion from synchronous serial data from a microcontroller to asynchronous, serial-data communication port such as RS-232, RS-485, IrDA. In this case the RS232 protocol is used. The MAX3100 includes a crystal oscillator and a baud rate generator with software-programmable divider ratios for all common baud rates from 300 baud to 230k baud. The transmitter section accepts SPI/MICROWIRE data, formats it, and transmits it in asynchronous serial format from the TX output. Data is loaded into the transmit buffer register from the SPI/MICROWIRE interface. The MAX3100 adds start and stop bits to the data and clocks the data out at the selected baud rate.

A software- or hardware-invoked shutdown lowers quiescent current to 10µA, while allowing the MAX3100 to detect receiver activity. An 8-word-deep first-in/first-out (FIFO) buffer minimizes processor overhead. This device also includes a flexible interrupt with four maskable sources, including address recognition on 9-bit networks. Two hardware-handshaking control lines are included (one input and one output).

Because of the features contained in its modules, the RS232 SPI click can be used for handheld instruments, UART in SPI systems, small networks in HVAC or Building control, battery-powered systems, PDAs, notebooks and many more.

RS232 SPI click offers a selection between 3.3V and 5V operation, with the onboard SMD jumper, labeled as VCC SEL. This allows both 3.3V and 5V MCUs to be interfaced with this Click board™.

Specifications

Type RS232
Applications Handheld instruments, UART in SPI systems, small networks in HVAC or Building control, battery-powered systems, PDAs, notebooks and many more
On-board modules MAX3100 MAX3100 serves as UART interface to the SPI/MICROWIRE compatible interface converter from Maxim Integrated; MAX3232, a 3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver from Texas Instruments
Key Features Operates up to 250 kbit/s, Operates With 3-V to 5.5-V VCC Supply, RS-232 Bus-Terminal ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM)
Interface SPI
Click board size L (57.15 x 25.4 mm)
Input Voltage 3.3V or 5V

Pinout diagram

This table shows how the pinout on RS232 SPI click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
NC 1 AN PWM 16 NC
Device shut down SDN 2 RST INT 15 INQ Interrupt Output
SPI Chip Select CS 3 CS RX 14 NC
SPI Clock SCK 4 SCK TX 13 NC
SPI Data OUT SDO 5 MISO SCL 12 NC
SPI Data IN SDI 6 MOSI SDA 11 NC
Power Supply 3.3V 7 3.3V 5V 10 5V Power supply
Ground GND 8 GND GND 9 GND Ground

Onboard settings and indicators

Label Name Default Description
LD1 PWR LED - Power LED Indicator
JP1 VCC SEL Left Power supply voltage selection: left position 3.3V, right position 5V

Software Support

We provide a library for the RS232 SPI Click on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Library Description

The library covers all the necessary functions that enables the usage of the RS232 SPI click board. User can send or receive data, check if data is ready or if tx line is busy, it is possible to change baud rate and to turn the device on or off.

Key functions:

  • uint8_t rs232spi_dataRead() - Function is used to read data from the receive register.
  • uint16_t rs232spi_dataReady() - Function is used to check if there is availavle data for reading.
  • void rs232spi_dataWrite( uint8_t wrData ) - Function is used to write into the transmit-buffer register.

Examples description

The application is composed of three sections :

  • System Initialization - Initializes SPI and LOG structures, sets RST pin as output and INT pin as input.
  • Application Initialization - Initialization driver enables SPI, sets up the device and starts write log.
  • Application Task - (code snippet) This example demonstrates the use of RS232 SPI click board by sending or receveing the message.
void applicationTask()
{
    uint8_t tmp;
    char rec;
    uint8_t mode = RS232SPI_WRITE_MODE;

    if ( mode == RS232SPI_READ_MODE )
    {
        // RECEIVER - UART polling
        if ( rs232spi_dataReady() != 0 )
        {
            rec = rs232spi_transfer( _RS232SPI_CMD_READ_DATA );
            mikrobus_logWrite( &rec, _LOG_BYTE );
        }
    }
    else if ( mode == RS232SPI_WRITE_MODE )
    {
        // TRANSMITER - TX each 2 sec
        for ( tmp = 0; tmp < 9; tmp++ )
        {
            rs232spi_dataWrite( MESSAGE_DATA[ tmp ] );
            if ( tmp < 6 )
            {
                Delay_ms( 100 );
            }
        }
        Delay_ms( 2000 );
    }
}


The full application code, and ready to use projects can be found on our LibStock page.

Other mikroE Libraries used in the example:

  • SPI
  • UART
  • Conversions

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

mikroSDK

This Click board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.

Resources

Downloads